Loganville Garage Door Repair: Garage Door Closure Problems

Garage door closure problems are not uncommon. Some issues that occur with garage doors are fairly straightforward and others take a bit more work and the hands of an expert. Loganville Garage Door Repair serves customers in Loganville, GA and we are here to go over garage door closure problems. If you are in our service area, feel free to call us with any questions at all. No matter where you are, we are confident that you will find this information to be beneficial.

Garage door closure issues can occur when:

There are safety sensor problems. At times, safety sensors will not work as they are supposed to. What are the safety sensors? They are a pair of twin sensors located at the bottom of the garage door. They sit roughly one inch above the ground. Facing toward one another, they work to send signals across the doorway’s length to make sure nothing is in the way when the garage door is attempting to close. Another problem could be that either or both of the sensors are not receiving the proper power. They could also be failing to emit the signal correctly. If this is the case, you are going to be left with a garage door that does not close completely. This is a safety feature in place for the customer so no one gets hurt. Sensors can always be replaced if need be.

There is something in the way, blocking the garage door. Of course, if a person is in the way, the garage door will not close all the way. Check the tracks, check under the garage door, check everywhere, including the surrounding area. The garage door will not close, or it should not close, if something is blocking it, telling it that something is in its path.

The sensors are misaligned. Maybe your sensors are actually functioning in the sense that they do work. They might actually be working; however, they are sending a message letting your garage door know that there is something in the way, which is causing it to not close completely. The sensors could be misaligned, in this case. How does this happen? One of the sensors might have been hit by mistake so it moved, or it could have just shifted. Check the sensor light because often times these will alert you when something is out of place. If you can see that the light is on how it always is, then everything should be aligned. However, if the light is blinking, the sensors might not be aligned with one another.
The cables are damaged. If the cables are damaged, your garage door might not close completely. Of course, whether or not the cables are there in this particular case will depend on the type of garage door opener you have. A cable could be frayed. You might need to call an expert to diagnose this particular concern because it might not always be very obvious.

The garage door springs are broken. The springs help your garage door to function, so while they are not big in size, they do have a big job. You will have a primary and secondary set of springs, like the overhead torsion springs. When these springs become damaged in any way, it can impact the garage door’s option to close completely. Balancing problems can also occur as a result of the garage door springs having wear and tear. You might not even need a professional to diagnose this problem for you, because you might be able to see that the springs have wear or tear, or that there is a gap in the spring, or that something otherwise looks off.

The travel distance setting might not be correct. Typically, garage door openers will have the option of telling the garage door how far it needs to go down to close completely. When the garage door opener was installed, this setting might not have been correct. Or, over time, the setting can somehow shift a little bit. When the travel distance setting is too high, it will tell the garage door to only close to a certain point, which might not be the ground. The garage door travel limit setting will just need to be adjusted.
The garage door tracks have damage. This is another potential issue that can lead to the garage door failing to close all the way. If the tracks are bent, warped or otherwise damaged in any way, the garage door will not close all the way. It could also be that the tracks are blocked. If you don’t see anything in the way, you might want to give an expert in your area a call. They will be able to come out and do an inspection.

Garage door closure problems are not uncommon – as a matter of fact, you should be able to now see that there are many different problems which can occur, causing your garage door to not close all the way or even at all. Some issues that occur with garage doors are fairly forthright, as you read above, and others take a bit more work and the hands of a garage door repair professional who is licensed and insured to provide the assistance that you need. Our company is one that serves customers in and near the Loganville, Georgia area, and we are hopeful that you now feel more knowledgeable regarding garage door closure problems. If you are in our service area, please go ahead and call us with any questions at all. We provide consultations and price quotes for free to locals, so you can get all the information you need without any pressure or hassle. And if you live outside of our service area, make sure to do a Google search to pull up a garage door repair expert near you. You can plug in “garage door repair service near me” and options should come up. Remember to take care of your garage door and keep your eyes open for any potential problems!